Tuesday, August 17, 2021

GE Window AC unit model AEL06LPL1 condensation pan drain hole location

 The GE Window AC unit model AEL06LPL1 has no proper drain hole to drain condensation from the unit. Instead it has a drain from the indoor section under the evaporator to the outside section under the condenser fan.  What's supposed to happen is that you mount the unit such that it's slightly higher on the inside, so condensation drips down the evaporator, then runs outside and into the "sling pan" under the condenser fan and gets slung into the condenser.


If this hole gets plugged from dust or dirt or whatever, water builds up in the inside section under the evaporator and starts dripping into the house.  Major pain.


I fixed this by taking off six sheet-metal screws on the outside section, prying the cover wide on left side as you're looking at it from the outside section, and using a long piece of #8 allthread, poking the drain passage until it started draining.  


It would have been really nice of the designers at GE to put an access port in the inside section of the unit to allow something to be poked through this drain passage.  But they did not.


I've gotten a lot of years out of this window unit, and it's operated great, energy efficient and good little cooler.  This is honestly the first trouble I've had with it.  Fortunately the water inside didn't ruin much.  Just some old magazines and a small section of drywall.  Frustrating though. 


Friday, February 22, 2019

Worst Customer Service Experience from Costco buying a refrigerator

This review was "moderated" by Costco, which means they refused to put my review on their website.

So I'm publishing it here.

Fridge arrived dented, did not make ice, the water stopped working after a day, major hassles getting a refund. 

Long version: Costco Shipped on 02/12/2019, Delivery Date:02/14/2019. They arrived at the house at about 1:30, which was in the noon-4PM window they said. They were on time. From there, things went downhill. 

Guys comes to deliver the fridge from Costco. They starts to disconnect the water line, and water spills out onto the floor. Delivery guy tells my wife that the valve isn’t holding, and says he may not be able to connect the new fridge, suggests setting it in the living room & not taking away the old fridge. He calls his boss to ask what to do. Meanwhile, Pearl looks at the valve and sees that it’s open. It’s a quarter-turn ball valve. She shuts it. HEY! Look! No more water leaking. Fine. So they install the new fridge. They tell her this is their 13th delivery today and they have five more to go. 

Oh look, there's a dent in the new fridge in a visible place. Fairly significant dent. 

I get on Costco Customer Service Chat online. They offer me $100 to keep the scratch-n-dent fridge. I say not enough, ship me a new one. 

They tell me in order to get a new one processed you would need to contact GE directly and get it processed through them as they do internal exchanges and require to set up delivery and pick up the same day with you. So I call GE. 

Called once 2:10pm 2/14/2019 – System hung up on me 

Called again 2:12 got a robot run-around then they hung up on me again 

Called again 2:14 PM, please hold for the next available agent, Trisa (Home Delivery Support) answered, said she needed to check on this unit to see if it’s available and asked me to hold (I just bought the bloody thing, you’d think it would be available). Came back on after a short time, said it is available (whoopee), and offered deliver on 2-21-2019. I said yes. She put me on hold for several minutes again to get that set up for us. She gave me return authorization number and said it would be delivered on 2-21-2019. 

That's A WEEK! 

15 hours after the new fridge is plugged in, it’s still not making ice, and it’s barely cold in the fridge section. The freezer section works. My daughter’s wedding is in a week, and we’ll have guests in the house starting a few days from now so now my wife wants me to postpone delivery of the new, hopefully undented fridge until March. I dread calling GE again and going through their idiotic robot system. 

Already overall this is the lamest experience I’ve had with Costco service. 

12:50 PM 2-15-2019: got on Costco Customer Support online chat, with LaQuita T: She could not help me at all, referred me to Costco Tech Support 1-866-861-0450. 

1:05PM 2-15-2019: Called Costco Tech Support, was on hold for 5+ minutes, then talked with Maria, she generated Case #. 

She Called GE. GE put her on hold. Maria made a Case # but could not help so transferred me to Costco.com to process a refund. 

Talked with Lee from Costco.com – he generated Service Request And said we would get a call within 5 to 7 days from the company to pick up the old fridge, and then I would get a refund. 

A week later a truck shows up with ANOTHER NEW FRICKING FRIDGE. When my wife says no, the driver marks “refused delivery” on the paper. He hauls away the broke fridge at her request. 

I get on the phone again to make sure the refund will be processed correctly. Called Costco.com 1-800-955-2292 spoke with Crystal at 2/21/2019 10:10AM, told her the tech who came today put on the paper that we refused delivery. Pearl told him that we did NOT refuse delivery, we asked for a refund not a replacement. The tech did indeed haul away the fridge Costco sent us. Crystal told me old (new) fridge was supposed to be picked up by “large freight” – then the refund would be processed She goes off line to connect with GE Appliance, I’m on hold for a long time. She’s online with GE appliance department – she will contact delivery driver to see why they brought out a new fridge. I’m back on hold waiting for that answer. Long hold. Crystal told me she had straightened it out and that yes, they did try to deliver a new fridge because one had been requested, but that they would process the refund within 3-5 days. Call ended 10:28 AM.

Wednesday, November 28, 2018

WALK OUT: Chris Mahar’s steely-eyed rules for buying a car, a truck, a horse, whatever:


OVERRIDING RULE: Always be ready to walk out. Always.  At all times.  No exceptions. Make your tolerance for walking out very, very low.  There are many dealers. You deserve what you tolerate.  Do not tolerate their crap

Note: this assumes you will get your own financing. If you're going with dealer financing you are at their mercy, and I pity you.

  1.  Walk out. Do not buy on the same day you first looked at the car.  Get the best price, then leave. Think about it.  Can you see yourself in this car?
  2. Tell the dealer, right up front, that there is only one number you're interested in; the drive-away-with-it price.  If they start trying to bury you with numbers, walk out.  This includes extras like rugs, window etching, paint coatings, and other sundry nonsense.  Walk out.
     
  3. Don't lie.  There's enough of that going on already.  And besides, there's nothing to be gained for you. If they lie, walk out.
     
  4. Before you buy, look with your own eyes at the actual title to verify this is not salvage, rebuilt, scrap. If they won't show it, walk out.
     
  5. Do not sign anything that has blanks or places not filled out.  Refuse to sign.  If they demand, walk out.
     
  6. Get everything in writing.  No verbal guarantees, warranties or promises.  They won't trust you, nor should they.  Don't trust them to act like anything but car dealers.
     
  7. Do not let the dealer run your credit more than once. Actually they shouldn't need to run it at all if you have your own financing. If they insist, walk out.
     
  8. Don't tell them how much you're willing to spend.  They'll ask.  Tell them you have your own financing.  After that, ignore them.  If they press, walk out.
     
  9. Don't bring a checkbook when buying a vehicle.  Don't bring a check. Set a price, then go get the money.
     
  10. Don't buy an extended warranty.  Don't pay to transfer one unless it's a spectacular bargain with nearly no restrictions.  They're universally a scam. If they insist, walk out.
     
  11. Take a nice long test drive, without the dealer if possible. If they won't allow it, be ready to walk out.
     
  12. Questions:
    1. What's the warranty?  What is not covered?
    2. Is the title clear? Show me
    3. Is it certified?  What does that mean for me?
       
      If you're buying new, you don't have to worry about a lot of this.  Still, always be ready to walk out.  Always.
       

 

Resources for buying a vehicle:

Auto Trader Magazine https://www.autotrader.com/

Kelly Blue Book https://www.kbb.com/


Costco Auto Program https://www.costcoauto.com/


True Car www.truecar.com


Tuesday, May 22, 2018

#LavaPorn - the best shots and videos of the volcanic eruption in Hawaii in May, 2018

I'm transfixed by shots of lava and the volcanic eruption that started in May, 2018. There are some awesome videos coming out, and as a service I'd like to capture and curate some of them here.






https://www.youtube.com/watch?v=pzHCd2X1GaM&t=328s
10 minute video of guys walking around and right up to the slow lava flows


https://www.youtube.com/watch?v=s1yV1kTrVGA
Helicopter footage of fast moving lava


https://www.facebook.com/USGSVolcanoes/videos/2035599389801945
Similar to above, helicopter video

https://www.youtube.com/watch?v=HtihmXFWqGo

Live footage of a lava geyser


http://www.news.com.au/technology/environment/hawaii-volcano-deadly-laze-could-be-released-as-lava-pours-into-ocean/news-story/b6db14773aec2aae08f0948f709a81be
Good news article with some great photos and videos

Reuters photos
https://www.reuters.com/news/picture/hawaiis-erupting-kilauea-volcano-idUSRTS1SEGD


https://www.youtube.com/watch?v=ddzU-rkzKF0


More Lavaporn. Turn the music off. It's just stupid. Also don't need to see the dumb grass-skirted bobble thing or rubber duck. We're in this for lavaporn, don'tcha know.

https://www.youtube.com/watch?v=_hbMLhcLWRs





Sunday, November 6, 2016

The Six Minute Career, by Chris Mahar

The Six Minute Career, by Chris Mahar
00:00:00 Jack felt a lightness in his chest as he accepted the first job of his new career, received his password, and logged into his new company’s internal website.  The training and education for this job had been grueling and at times painful, like a hot knife in his brain.  But he’d demonstrated the right propensity, and stuck with it to become a design engineer specializing in plasma flow measurement.
00:00:05 The task list immediately appeared on his augmented reality headset, and began scrolling by.  Jack’s breath hitched and he put a shaky hand to his forehead over his AR visor. There was so much to do.
00:00:10 He took a deep breath, savoring this moment of starting a new career, then dove into the task list, prioritizing and sequencing based on the new knowledge in his head from the intense learning session he’d just completed. The new auto-teaching system imprinted directly onto the brain, overlaying a new career over any old ones that were already there.  The process was like a knife to the skull, but lasted only a minute, and at the end left you fully trained to begin a new career, albeit with a very narrow specialty. General training took longer, usually several minutes, but was only available to certain people who had a capacity for it.  Being a specialist and not a generalist, Jack’s training never took long, and when it ended he always felt puffed up and fidgety, ready to take on the new and unfamiliar job.
00:00:20 Other workers appeared in his peripheral vision, and he got a hint of the people he was working with on the project, redesigning a spacecraft plasma pump from an old class of freighters. It wasn’t the most glamorous job, but first jobs in any career rarely were.  
The command interface wouldn’t let him focus on the people around him, but it allowed him to be aware of their rough appearance, their roles in the job, and, vaguely, their gender and manner of dress.  They weren’t physically present in the workstation with him, of course.  They were augmented reality manifestations of real people all over the world who had been specially trained for this type of work, and hired for this job based on their specialty.  But being together virtually aided in the work because they could each see what the others were doing, which allowed brief but potent interactions that furthered the project.
00:01:00 Jack heard their voices around him asking and answering questions, giving data, acknowledging tasks on the list and adding more tasks as the job took form.  As he worked, adding his details to the job, designs appeared on his AR.  He manipulated them, added the bits he was responsible for, and checked what others had done that related to his work.  Slowly at first, but with gaining speed, he ticked tasks off his list.
00:02:14 Red warnings flashed on his AR, indicating he’d made an error that conflicted with someone else’s work.  Several men swore, and one woman giggle.  He instinctively turned to apologize and got a glimpse of a thin Asian woman with her arms crossed and face tightened.  Then the AR caught up with his motion and put his work front and center, the woman appearing only as a shadow to one side.  He corrected his mistake, rerouting tubing that interfered with her work while muttering an apology.  He heard sighs and chuckles from a few of the others.  He thought he heard one of them say, “Noob,” but wasn’t sure.  The AR normally only amplified and transmitted discussion that related to the job, so he may have mis-heard.
00:02:45 Red faced from embarrassment, Jack continued working. The design was taking shape, and he worked feverishly to keep up, making sure his small part of the work followed the design principles, fit harmoniously with the whole, and interfaced neatly with other systems on the overall job.  As it came together he felt his face relax, and some of the tension in his chest eased.  He learned of a new innovative ceramic alloy that popped up in a window on the corner of his view, and incorporated it into his design section, then noticed that several others had also included the new alloy in their sections.  It allowed the part to be even lighter and stronger than originally designed, and he sat a bit straighter in his chair, his eyes bright from the improvement to the design.
00:03:30 He noticed others leaning back from the job, reclining slightly in their chairs, and heard a bit more bluster in their comments and questions to each other.  Some even criticized the work of others, despite the final part exceeding goals and design specifications listed when the job had began.  He could see that they were looking around, but knew the AR interface wouldn’t let them look away from the job for more than a fraction of a second before it adjusted.  Careers were so short these days that there was not time to be wasted on socialization. Jack had heard about a time when people had only six or seven careers in their lifetime.  He had lost count of all the careers he’d had.  He had memories of dozens of careers, but knew that when the imprint overlayed onto your brain, some knowledge was pushed out or overwritten, and he was sure he’d had many more careers than he remembered.
00:04:40 Work on the project was slowing as the last few touches were placed on the design of the part.  Jack knew, from his flash training, that once the part was designed, it would be mass produced, likely for several days, until a newer model was needed. He took a moment to glance at a journal article his command interface had flagged as related to this project, and saw in the summary that plasma flow measurement technology had advanced since this job had started, and much of what he’d learned about it was now obsolete.  He considered taking a refresher course, but this project was so close to completion that he couldn't spare time away from it.  
00:05:25 Jack’s part of the work was essentially finished, but he couldn’t legally post for another job until he received notice he’d been released for this one, which seemed particularly unfair.  He twisted his hands together as he scanned journals with a sinking feeling in the pit of his stomach.  Technology had moved so quickly while he worked that nearly everything he’d learned no longer applied.  A refresher course wouldn’t suffice. If he was going to stay with this speciality, he would have to get educated all over again.
00:05:35 Jack’s release slip appeared on his AR visor, an electronic  pink slip indicating that he would be released in 30 seconds with a reasonable bonus, and that this company had no further work for him.  No hope of another job here.  He gritted his teeth and thought that it was inconceivable that this company, the biggest spaceship design outfit in the solar system couldn’t find another job for him, especially after all the fine work he’d done on this job. He heard others in the virtual room groan as they got the same news.
00:05:39 Jack posted his resume on the job boards, hopeful that one of the smaller design firms might have work for an experienced and skilled plasma flow design engineer. The virtual room would evaporate in just a few seconds, and others were discussing what they might pick as their next career. The medical field seemed like a popular choice.
00:05:49 His gaze darted over the job specifications scrolling by, fingers twitching involuntarily, but no jobs offers appeared in his specialty.  His shoulders sank as he realized he would definitely have to learn a new career.
00:06:06 His arms fell to his side, lifeless, as he thought about his decision picking this career. One job. It had lasted one job. Again.  Why did this keep happening? The career counselor had been so sure that specializing  in plasma flow measurement would guarantee him jobs well into the future. Of course, he hadn’t paid extra for that councilor, taking whatever the school offered. And he knew that large corporations paid colleges to give advice and counseling that worked to their advantage. He clenched his fists in anger.  Didn’t the school have an obligation to their students?
00:06:19 Alright, he thought. He had allowed himself his moments of pity. Now he leaned forward in the chair, eyes brightening, and dialed up the college catalog, prioritizing careers based on the latest career counseling advice. It was time he picked a new career. This time he’d find one that got him more than one job before it became obsolete.  This would be his seventh career before lunch break, and he was determined to make it last into the afternoon.  He picked a promising career from the menu, and keyed up the neural interface, feeling that familiar hot knife in the brain sensation.  This time he would be a medical instrumentation designer specializing in wireless kidney implant monitoring.  His knowledge of plasma flow faded, and through the pain of imprint he felt a surge of pride in his new career.

Friday, October 23, 2015

How To Be The Ugly American - A Guide to Ridiculing Foreign Countries & Their Inhabitants for Fun and Self-Satisfaction


You should always be respectful of other people’s culture, even if they're primitive backwards cultures that includes things illegal in America since before our founding; even if the culture includes  socialism, a pathetic work ethic, earth-worshiping heathen religions, oppression of gays & women, atrocious fashion trends, insufficient indoor plumbing, absurd civil engineering, a complete lack of regard for any traffic laws, and an abysmally low regard for human life.  All cultures might not be equal, but we’re supposed to pretend that they're equal.

However, don’t let being respectful of these medieval cultures keep you from mocking them unmercifully.  Do you think Romans in ancient times didn’t respect the foreign cultures they conquered? Of course they did. That's why they conquered them.  Also there was the tribute, the slaves & the expanded territory, but always there was respect.  And mocking. Don't imagine that these two things are mutually exclusive.

Since American culture has already conquered pretty much every other culture on the planet, and they’re already paying us tribute by buying our technology, our weapons, our food, clothes, movies and pretty much everything else, we can afford to treat them with respect while simultaneously mocking them.

But HOW should we mock them, you ask?  For the benefit of all US travelers to foreign lands, I have written this guide.  These are just suggestions, and I welcome comments and additional ideas.  Also, I am not responsible if you get beat up.  However, with the proper application of sarcasm and snark, you can get away with most of these with only a few glances of disgust and ill will.
Try some. They're fun.
  • Ask for the price of everything in dollars. “I don’t care how much monopoly money it cost, what’s the price in REAL dollars?”
  • Similarly, any time a measurement is given in meters, centimeters, kilometers, etc, ask, "What does that translate to in real American units?"
  • Wear shorts everywhere.  And tube socks.
  • Lean close and ask, slowly and slightly louder than normal, “Do   You   Speak   American?” 
  • Complain about the tiny sinks, the itty-bity toilets, the narrow stalls and the generally primitive plumbing. “Doesn’t anyone around here know about the wide stance? Or is that just an American thing?”
  • Ridicule soccer.  Refuse to call it 'football'.  Instead, refer to it as 'that pansy kickball game'.  Ridicule Cricket even worse. 
  • When viewing some ancient building or structure, say "They should really clean this place up.  If they picked up all these broken columns and stacked up all that stuff that's been knocked over it would look a lot better."  Also, "This place sure could use a coat of paint."
  • Ask where you can get a real American meal.
  • In your suitcases, pack more clothes than they even own in their backwards, mudpit country.  This works best if they have to carry your luggage for you.
  • Ask if they still have a king, or an emperor, or whatever strange form of government they have.  No matter what the answer, act surprised.  “You still have a queen here? That’s weird.”
  • Ask, “Is it safe to drink the water in this country?”
  • Scrunch up your nose in disapproval and ask, “Are you Italian?”  Always pick a country other than the one you’re in.
  • When viewing priceless ancient artifacts, say, "That would look so great hanging on the wall of my rec room."  If it's ancient pottery or golden pitchers, goblets or bowls, say, "Man, that would make an excellent salsa dish." 
  • Ask, “What language do you’all speak in this country?”
  • Remember: ONLY America is America. Just b/c a country is on a continent named North America, or Central America, or South America doesn't mean it's America. 
  • Don’t adapt to their cultures. After all, they all want to come to America, so make them adapt to you.
  • Order hamburgers whenever you want, and in any sort of restaurant you happen to be in. It’s not like they don’t know what a hamburger is, and they can make one for you. When it comes, eat it with your hands like it was meant to be eaten, & not with a fork and knife.
  • Ask for a hot dog whenever and wherever you happen to be.
  • If you’re in Mexico and have a street taco, loudly compare it to tacos at Taco Bell & say “Taco Bell does it better.”  Same thing for Chinese food in China, “Panda Express food is way better than this.”  Same thing in Italy with pizza; “Heck, we have better pizza than this at Costco!”  By the way, it's true.
  • When ordering a beer in Germany, ask for Bud Light.  If they say they don’t have it, ask what American beers they DO have?
  • When in England eating French fries (they call them chips, but you don't have to), & they try to give you vinegar, demand ketchup. When in France, ask for Ranch dressing.  When in Belgium, ask for Hershey's chocolate.
  • If you meet a Canadians, say, “Oh, well you're practically the same as real Americans” because they love that.
  • Whine about all the people smoking.
  • Mock their drinking sodas without ice.  “What? They don’t have ice machines in this primitive country?”
  • Wear a baseball hat all the time.  Who cares if the rest of the world doesn’t have baseball.  They should.
  • Eat only at McDonalds, Starbucks or any good solid American chain.
  • Complain about the foreign languages. “It’s like they have a different word for EVERYTHING. If they want to be understood, why don’t they just speak American?”
  • Ask for translation for words that don’t translate.  “How do you say ‘Coca-Cola’ in French?”
  • If they ask you where you’re from, stick your chest out and say, “I’m from the United States.”  Of course they already know that. You're an American, so you stick out like a sore thumb. But say it anyway, just to rub it in.
  • Frequently remind all Europeans that the US bailed them out in two world wars.

Remember, they may hate us, but they love our money, and most of them would move to our country, legally or illegally, if they could. Heck, it seems like half of them are already here, either collecting welfare, or standing out front of Home Depot waiting for a day job. Or both.

Friday, February 6, 2015

Cheapskate Astronomer Builds A Sky-Tracker from a 24 Hour Timer

A couple years ago I saw the IOptron Skytracker.  Choked on the price.  $400? Really?

OK, it's DC. It will work anywhere. That's cool.  It's got a lot of torque, and an angle-adjuster built right on to it.  Nice.

But $400?  Dang.

Being the Cheapskate Astronomer, it occurred to me that a 24 hour timer went around once each day. That should work, as long as it rotates in the right direction.

I got mine at Home Depot during Christmas time when they had it in the Christmas decoration section.  It was just under $5.

Now you have to plug these things in, so it won't work out away from electrical power.  That is the big downside of this plan.

Also at Home Depot, I find that a 1 1/4 inch PVC union fits right on the part that turns.  It is important to note that the quarter-size part in the center does not rotate.  Only the outer ring with all those gray thingys you pull up or push down turns.

So here's what I buy.

That's a 1 1/4 inch union, a same size cap, a 3/4 inch 1/4-20 hex head bolt, zinc coated, a couple of nuts and fender washers.  I ended up using only one of the fender washers and one of the nuts.

Drilled a hole in the center of the cap.

Installed the bolt, washer and nut.
Now, tricky part. Glue the PVC union on to the dial of the timer. Work slowly and carefully, getting it centered, but don't let ANY GLUE get on the part between the dial and the part that doesn't turn.  I used superglue.
And here's how it looks glued up.
To mount the thing to a tripod, I simply glued a piece of wood to the back, then used a clamp to clamp that to the head of a cheap $20 tripod.  The tripod head has pan and tilt on it, so I lined the pipe union up with the North Star.

Then get your camera all ready, and mounted on the cap on the 1/4-20 bolt. Looks like this:
Without a multi-angle mount (ball-joint) I can't aim the camera anywhere but at the celestial equator.

Also, the piece of wood I glued on to the back of the thing interfered with the extension cord, so I had to trim it with a Dremel tool to allow the extension cord plug to plug all the way into the back of the timer.

But it worked.  It bore the weight of this small camera, and rotated, keeping aimed at one part of the sky the whole time.

With a ball-joint mount, I'll be able to point the camera anywhere in the sky.

And with that Canon Powershot camera and CHDK, I can take up to 15 second exposures and a script for intervelometer features, and take long exposure images of one part of the sky all night long, or at least until the batteries in the camera are drained.  Use rechargeable Li-ion batteries and you get a couple hundred images at least.

Total cost is less than $10 for the sky-tracker.
I'm not the first to try this. Here's one http://www.instructables.com/id/Standalone-mount-for-astro-photography/

and here's another: http://www.hkastroforum.net/viewtopic.php?t=26221&sid=04811df9e261b1af3